For those just starting to take their first steps into electronics, it is important to start somewhere. Well, we invite you to familiarize yourself with ideas that may come in handy in the future and at the same time give you an idea of how something should be done. What to choose if you want to make simple ones with your own hands? Here are options that can be used in everyday life.

Simple power regulator for smooth switching of lamps

This type of device has found wide application. The simplest is a regular diode, which is connected in series with the load. Such regulation can be used to extend the life of an incandescent lamp, as well as to prevent overheating of the soldering iron. They can also be used to change power over a wide range of values. First, there will be the simplest DIY electronic crafts. You can see the diagrams here.

How to protect yourself from mains voltage fluctuations

This device turns off the load if the mains voltage is outside the permissible limits. As a rule, a deviation of up to 10% from the norm is considered normal. But due to the peculiarities of the energy supply system in our country, such limits are not always observed. So, the voltage can be 1.5 times higher, or much lower than necessary. The result is often unpleasant - the equipment fails. Therefore, there is a need for a device that will turn off the load before something has time to burn out. But when creating such a homemade product, you need to be careful, since the work will be carried out with considerable stress.

How to make a safety transformer

Transformerless power supplies are often used in various electronic designs. Typically, such devices have low power, and to avoid electrical injury, they are placed in an insulating plastic case. But sometimes they need to be configured, and then the security is broken. To avoid possible injury, use an isolating safety transformer. It will also be useful when repairing such devices. Structurally, they consist of two identical windings, each of which is designed for the network. As a rule, the power of transformers of this type ranges from 60-100 W; these are the optimal parameters for setting up various electronics.

Simple emergency lighting source

What should you do if you need to ensure that some area remains illuminated in the event of a power outage? The answer to such calls can be an emergency lamp made on the basis of a standard energy saving lamp, the power of which does not exceed 11 watts. So if it is necessary for the light to be somewhere in the corridor, utility room or at the workplace, this homemade product will come in handy. Usually, if there is voltage, they operate directly from the mains. When it disappears, the lamp begins to function on battery power. When the mains voltage is restored, the lamp will work and the battery will automatically charge. The best electronic DIY projects have been left for the end of the article.

Boost power regulator for soldering iron

In cases where it is necessary to solder massive parts or the mains voltage often drops, using a soldering iron becomes problematic. And a step-up power regulator can help out of this situation. In these cases, the load (i.e., the soldering iron) is powered using rectified mains voltage. The change is carried out using an electrolytic capacitor, the capacitance of which allows you to obtain a voltage greater than 1.41 network voltage. So, with a standard voltage value of 220 V, it will give 310 V. And if there is a drop, say, to 160 V, then it will turn out that 160 * 1.41 = 225.6 V, which will allow for optimal operation. But this is just an example. You have the opportunity to make a scheme that is suitable specifically for your conditions.

The simplest twilight switch (photo relay)

As new parts are created, fewer components are now needed to make a device. Thus, for a regular twilight switch, only 3 of them are needed. Moreover, due to the versatility of the design, multi-purpose use is possible: in apartment building; for lighting the porch or courtyard of a private home, or even a separate room. Pointing out the features of such a design as a twilight switch, it is also called a “photo relay”. You can find many implementation schemes that were made either by amateurs or industrialists. They have their own set of positive and negative properties. Negative properties are usually either the need for a constant voltage source or the complexity of the circuit itself. Also, when buying cheap and simple parts or entire sets, they often complain that they simply burn. The functionality of the scheme is based on three components:

Photocell. It is usually understood as photoresistors, phototransistors and photodiodes.
Comparator.
Triac or relay.

When there is daylight, the resistance of the photocell is low and does not exceed the response threshold. But as soon as it gets dark, the structure will be turned on at that very moment.

Conclusion

Here are some interesting electronic crafts you can make with your own hands. The main thing in cases where something doesn’t work out is to keep trying, and then everything will work out. And after gaining experience, it will be possible to move on to more complex schemes.

So. Life has turned out in such a way that I have a house in the village with gas heating. It is not possible to live there permanently. The house is used as a summer house. For a couple of winters I stupidly left the boiler on with the minimum coolant temperature.
But there are two disadvantages.
1. Gas bills are astronomical.
2. If there is a need to come to the house in the middle of winter, the temperature in the house is around 12 degrees.
Therefore, it was necessary to invent something.
I'll clarify right away. The presence of a WI-FI access point in the relay coverage area is mandatory. But, I think, if you get confused, you can put a connected mobile phone next to the sensor and give out a signal from the phone.

Connecting a 4-pin motion sensor with your own hands (diagram)

DIY motion sensor connection diagram

It happens that you need to install lighting in your dacha or in your home. will be triggered by movement or a person or someone else.

A motion sensor, which I ordered from Aliexpress, works well with this function. The link to which will be below. By connecting light through a motion sensor, when a person passes through his field of vision, the light turns on and stays on for 1 minute. and turns off again.

In this article I’ll tell you how to connect such a sensor if it doesn’t have 3 contacts, but 4 like this one.

DIY power supply from an energy-saving light bulb

When to get 12 Volt for LED strip , or for some other purpose, there is an option to make such a power supply with your own hands.

DIY fan speed controller

This regulator allows for smooth adjustment variable resistor fan speed.

The circuit of the floor fan speed controller turned out to be the simplest. To fit into the case from an old Nokia phone charger. The terminals from a regular electrical outlet also fit in there.

The installation is quite tight, but this was due to the size of the case..

DIY plant lighting

There may be a problem with lack of lighting plants, flowers or seedlings, and there is a need for artificial light for them, and this is the kind of light we can provide on LEDs with your own hands.

DIY brightness control

It all started after I installed halogen lamps for lighting at home. When turned on, they often burned out. Sometimes even 1 light bulb a day. Therefore, I decided to make a smooth switching on of the lighting based on a brightness control with my own hands, and I am attaching a diagram of the brightness control.

DIY refrigerator thermostat

It all started when I returned from work and opened the refrigerator to find it warm. Turning the thermostat control did not help - the cold did not appear. Therefore, I decided not to buy a new unit, which is also rare, but to make an electronic thermostat myself using the ATtiny85. The difference with the original thermostat is that the temperature sensor is on the shelf and not hidden in the wall. In addition, 2 LEDs appeared - they signal that the unit is turned on or the temperature is above the upper threshold.

DIY soil moisture sensor

This device can be used for automatic watering in greenhouses, flower greenhouses, flower beds and indoor plants. Below is a diagram on which you can make a simple sensor (detector) of soil moisture (or dryness) with your own hands. When the soil dries out, voltage is applied with a current of up to 90 mA, which is quite enough, turn on the relay.

It is also suitable for automatically turning on drip irrigation to avoid excess moisture.

Fluorescent lamp power supply circuit

Power scheme fluorescent lamp.

Often when it fails energy saving lamps, in It burns out the power circuit, not the lamp itself. As is known, LDS with burnt filaments, it is necessary to supply the network with rectified current using a starterless starting device. In this case, the filaments of the lamp are shunted with a jumper and to which the high voltage to turn on the lamp. There is an instantaneous cold ignition of the lamp, with a sharp increase in the voltage on it, upon start-up without preheating the electrodes. In this article we will look at starting an LDS lamp with your own hands.

USB keyboard for tablet

Somehow, suddenly, I took something and decided to buy a new keyboard for my PC. The desire for novelty is irresistible. Changed the background color from white to black, and the letter color from red-black to white. A week later, the desire for novelty naturally disappeared like water into sand (an old friend is better than two new ones) and the new thing was sent to the closet for storage - until better times. And now they came for her, she didn’t even imagine that it would happen so quickly. And therefore the name would be even better suited not which is, but how to connect a usb keyboard to a tablet.

Every day there are more and more, many new articles appear, it is quite difficult for new visitors to immediately find their bearings and review at once everything that has already been written and previously posted.

I would really like to draw the attention of all visitors to individual articles that were posted on the site earlier. In order to avoid having to search for the necessary information for a long time, I will make several “entrance pages” with links to the most interesting and useful articles on individual topics.

Let's call the first such page "Useful electronic homemade products." Here we consider simple electronic circuits, which are available for implementation to people of any level of training. The circuits are built using a modern electronic base.

All information in the articles is presented in a very accessible form and to the extent necessary for practical work. Naturally, to implement such schemes you need to understand at least the basics of electronics.

So, a selection of the most interesting articles on the site on the topic "Useful electronic homemade products". The author of the articles is Boris Aladyshkin.

Modern electronics components greatly simplify circuit design. Even a regular twilight switch can now be assembled from just three parts.

The article describes a simple and reliable electric pump control circuit. Despite the extreme simplicity of the circuit, the device can operate in two modes: water lifting and drainage.

The article provides several diagrams of spot welding machines.

Using the described design, you can determine whether a mechanism located in another room or building is working or not. Information about the operation is the vibration of the mechanism itself.

A story about what a safety transformer is, why it is needed and how you can make it yourself.

Description of a simple device that turns off the load if the mains voltage exceeds acceptable limits.

The article discusses the circuit of a simple thermostat using an adjustable zener diode TL431.

An article about how to make a device for smoothly switching on lamps using the KR1182PM1 microcircuit.

Sometimes, when the voltage in the network is low or when soldering massive parts, it becomes simply impossible to use a soldering iron. This is where a boost power regulator for a soldering iron can come to the rescue.

An article about how you can replace a mechanical thermostat for an oil heating radiator.

Description of a simple and reliable thermostat circuit for a heating system.

The article provides a description of the converter circuit, made on a modern element base, containing minimum quantity parts and allows you to obtain significant power in the load.

Article about in various ways connecting the load to the control unit on microcircuits using relays and thyristors.

Description of a simple control circuit for LED garlands.

The design of a simple timer that allows you to turn the load on and off at specified intervals. Working time and pause time do not depend on each other.

Description of the circuit and operating principle of a simple emergency lamp based on an energy-saving lamp.

A detailed story about the popular "laser-iron" manufacturing technology printed circuit boards, its features and nuances.

Manufacturing electronic homemade products Do it yourself gained popularity back in the last century, when semiconductor devices appeared. With their help from old equipment it was possible to simply assemble the devices necessary for everyday life. Today, repair and assembly of equipment for the home or cottage, for a car or garage can also be solved at home.

[Hide]

Homemade devices for home and garden

Electrical homemade products for home and garden that use the power of electricity can be made by every electrician. Most devices are created using factory components and require only school knowledge of electricity.

Electric kebab maker

The electric kebab maker can be either horizontal or vertical. Stores usually sell vertical ones, and they do their job well after some modification.

To create a horizontal barbecue grill you will need a heating element and a frame resembling a barbecue. The heating element can be made from a ceramic tube and a nichrome spiral wound around it. The tube is secured through an insulating material in a metal casing. Drawings will be required to assemble the case.

Barbecue grill

An equally interesting idea is a kebab grill with an electric drive for rotating skewers. By adding an electric motor to a regular grill, you can get an excellent device that will cook barbecue in autonomous mode. To organize the skewer drive, you can use a motor from the wipers, from washing machine or any other 12 Volt. Using a system of pulleys and a belt or gear drive, the rotation of the shaft is transmitted to the skewers, and the meat is slowly turned over the coals.

Homemade WI-FI antenna

This antenna will improve the reception quality and Wi-Fi speed in your home. According to reviews, after connecting it, the signal level rises from 5 to 27 Mbit.

For production you need:

a small metal sieve or colander;
Wi-Fi adapter (USB);
USB cable;
drill;
epoxy resin;
camera tripod;
plastic clamps.

Manufacturing process:

We drill a small hole (14 mm) in the center of the sieve and insert a metal pin into it to secure the adapter.
Insert the connector from the USB cable into the prepared hole and secure it with epoxy resin. The USB connector after gluing must be strictly perpendicular to the plane of the sieve, then the device will work more efficiently.
Then, using two zip ties, “ears” are made through which the cable is attached.
We fix the product on a camera tripod. We drill a hole with a diameter of 12 mm in the antenna and tighten it with a nut.

Required materials Insert the pin into the drilled hole Glue the USB cable Securing the cable Tripod Installing the antenna using a tripod

Electrical homemade products for the garage

Let's consider several projects useful homemade products for the garage.

Homemade chandelier

If you have poor lighting in your garage, then a makeshift chandelier will be very useful. To make a bifurcating chuck, you will need a pair of angular chucks, which are sold at a regular hardware store.

Sequence of actions:

We remove the wires from the sockets and fasten them with a plastic tie. We get a socket for two lamps. All that remains is to connect them to the electrical network.
To do this, we use the base of a fluorescent lamp. Carefully break out the lamp, then solder the wires from our design to the contacts of the base.
We insulate them well and attach the base on top of the cartridges.

The use of conventional light bulbs in this design is undesirable - the sockets may melt from heating.

LED device

Another lighting option could be a homemade LED lighting device.

To make it you will need:

old fluorescent lamp;
LED strip;
connecting wires.

The manufacturing sequence is as follows:

An LED strip is glued to the lamp body in one or several rows.
The connecting wires are connected and brought to the lamp switch.
The assembled device is tested.

Spot welding machine

A necessary device in the garage will be homemade apparatus for spot welding, the basis of which is a transformer from an old microwave oven. Prerequisite— the transformer must be working in order not to rewind all the windings.

The process of assembling the welder is quite simple:

The transformer is dismantled.
Carefully remove the secondary winding.
Two shunts are removed.
A secondary winding of two or three turns is made of thick wire (with a diameter of at least 10 mm).
Electrodes for resistance welding are made from a copper rod with a diameter larger than the wires.

Homemade spot welding tool

Useful DIY items for fishing

Among the homemade products you can find a lot interesting ideas for use in hiking conditions, as well as hunting and fishing.

Electronic alarm

An example would be an electronic signaling device for fishing with a regular fishing rod or other equipment. A simple biting device can be assembled in just half an hour. For it you will need an old beeper keychain and a strip of plastic 1-2 mm thick.

Alarm assembly:

The keychain is attached to the rod.
A strip of plastic is glued to the fishing line and inserted between the contacts of the key fob.

Now when the fish bites, the fish will pull the line, the plastic will fly out, the contacts will close and the key fob will work.

Underwater camera for ice fishing

Using a homemade underwater camera for winter fishing, you can see if there is fish under the hole. And this simplifies the fishing process.

To make it you will need:

small camera;
sealed camera box;
small TV;
car battery to power the camera;
extension;
inverter;
lead for cargo;
ultraviolet diodes for illumination during underwater shooting;
superglue, electrical tape, sealant.

Build process:

Two holes are made in the upper part of the box. An extension cable is inserted through one. Through the second is the wire that connects the camera to the TV.
Several more holes are made in the box into which light bulbs are inserted for illumination. The wires from the light bulbs are soldered into one circuit (for example, with a parallel arrangement), which is connected to a cable that provides power.
The holes are sealed with glue and tape for a tight seal.
Melt the lead and pour out small elongated bars from it. They are placed at the bottom of the box.
Set up the camera and connect it to the cable. After which it is carefully placed in the box so that it has a clear forward and horizontal direction and transmits a high-quality image. For stability, the chamber is surrounded by soft material.
A torso (rope, belt) is attached to the box, which will be used to lower the camera to depth. For convenience, you can combine it, the power cable and the communication wire between the video camera and the TV into one core, secured with electrical tape.
Connect the power cable of the video camera to the battery and test the device.

Homemade fish bait

You can make a good bait for fishing yourself. This will be a device assembled on the basis of a simple multivibrator.

You will need:

sound emitter, for example, from a children's toy;
wires;
a small plastic jar, for example, for medicinal tablets;
electronic board;
regulator with plastic rod;
a piece of foam;
batteries;
weights for the float;
volume control.

The bait is assembled as follows:

You need to solder the circuit and check it.
Two wires are soldered to the sound emitter. Then they are carried inside the case and connected to the board.
A regulator with a plastic rod is placed in the lid of the jar.
A dense circle cut out of foam plastic is installed on top of the board, which separates the board from the battery.
Weights are attached to the bottom of the jar so that the container floats on the water like a float.
The regulator sets the frequency and changes the sound.

Bait scheme - 1 Bait scheme - 2

Electronic homemade products for cars

Car enthusiasts create homemade products with their own hands to improve appearance and ease of use of the car.

Electrical auto tester

A simple homemade electrical probe is perfect for a car. It can show the presence in electrical circuit voltage of 12 volts. It is used to check the serviceability of relays, as well as light bulbs and other equipment. You can make such a device from a syringe and LEDs.

Assembly diagram:

Two LEDs are soldered with opposite terminals (plus one to the minus of the other and vice versa).
A steel probe is connected to one of the solders through a resistance of 300 Ohms. To the other solder there is a contact for batteries.
The design is inserted into the syringe so that the probe comes out of the hole for the needles. Most of the probe is insulated with a PVC pipe.
4 LR44 batteries are inserted into the syringe so that one of the poles is connected to the LED contact.
The other pole of the batteries is connected to a flexible wire with an alligator clip.

The video explains how to make a syringe tester. Filmed by ILYANOV channel.

Light switch

The scheme for smoothly turning off the lights in the car interior is quite simple to manufacture. Such electronics are suitable for any car. A small board consisting of a capacitor and diodes is soldered parallel to the interior lamp terminals. The drop in electricity voltage will occur gradually and create the effect of a gradually fading light.

Car subwoofer

To make a car subwoofer with your own hands, you must first purchase a speaker. You need to start from its dimensions when calculating the size of the case.

The simplest and most suitable form of a subwoofer for the trunk is a truncated pyramid with a slope similar to that of the rear seats.

LED fog lights

You can make LED car foglights with your own hands.

For creativity you will need:

two ten-watt LEDs;
2 lenses from an old projector;
gaskets from plastic pipes;
LM317T microcircuits;
resistors.

Instructions for assembling the craft:

LEDs are installed on pre-prepared aluminum radiators.
The structure is assembled from headlight housings, lenses from projectors, gaskets and diodes on radiators.
The fog lights are powered through current stabilizers on LM317T microcircuits and resistors.

Car carrying

A very convenient car carrier is made from a computer USB lamp. It is compact and you can connect the device to any place in the car wiring.

Manufacturing scheme:

Remove the contacts from the USB plug.
In the plug body we connect the wires of the lamp and the car alligator clips.
To mount it in the right place (even horizontally), a magnet is placed on the plug.

Since you have decided to become a self-taught electrician, then probably after a short period of time you will want to make some useful electrical appliance for your home, car or garden with your own hands. At the same time, homemade products can be useful not only in everyday life, but also made for sale, for example. In fact, the process of assembling simple devices at home is not difficult at all. You just need to be able to read diagrams and use the ham radio tool.

As for the first point, before you start making electronic homemade products with your own hands, you need to learn how to read electrical circuits. In this case, ours will be a good helper.

Among the tools for novice electricians, you will need a soldering iron, a set of screwdrivers, pliers and a multimeter. To assemble some popular electrical appliances, you may even need a welding machine, but this is a rare case. By the way, in this section of the site we even described the same welding machine.

Special attention should be paid to available materials, from which every novice electrician can make basic electronic homemade products with their own hands. Most often, old domestic parts are used in the manufacture of simple and useful electrical appliances: transformers, amplifiers, wires, etc. In most cases, novice radio amateurs and electricians just need to look for all the necessary tools in a garage or shed in the country.

When everything is ready - the tools have been collected, spare parts have been found and minimal knowledge has been obtained, you can proceed to assembling amateur electronic homemade products at home. This is where our small guide will help you. Each instruction provided includes not only detailed description each stage of creating electrical appliances, but is also accompanied by photo examples, diagrams, as well as video lessons that clearly show the entire manufacturing process. If you don’t understand some point, you can clarify it under the entry in the comments. Our specialists will try to advise you in a timely manner!