RENTED CALIBRATED HEXAGON.
ASSORTMENT
GOST 8560-78
USSR STATE COMMITTEE ON STANDARDS
Moscow
STATE STANDARD OF THE USSR UNION
RENTED CALIBRATED HEXAGON. ASSORTMENT Rolled-stock calibrated hexahedronal. Range of products. |
GOST In return |
|
By Decree of the USSR State Committee on Standards dated August 2, 1978 No. 2079, the introduction date was set |
||
01.07. 1979 |
||
The validity period was lifted according to Protocol No. 7-95 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-95)
1. This standard applies to calibrated hexagonal rolled products ranging in size from 3 to 100 mm.
(Changed edition, Amendment No. 2).
2. The dimensions of the rolled section and the maximum deviations for them, depending on the accuracy classes, must correspond to those indicated on 1 and c.
Rolled size (diameter of the written circle A or turnkey size), mm |
Maximum deviations, mm |
Diameter of circumscribed circle, A, mm |
Maximum deviations, mm |
Cross-sectional area, mm 2 |
Weight of 1 m length, kg |
||
h 10 |
h 11 |
h 12 |
|||||
0,040 |
0,060 |
0,100 |
7,79 |
0,061 |
|||
0,048 |
0,075 |
0,120 |
8,87 |
0,070 |
|||
10,61 |
0,083 |
||||||
13,86 |
0,109 |
||||||
17,54 |
0,138 |
||||||
21,65 |
0,170 |
||||||
26,20 |
0,206 |
||||||
31,18 |
0,245 |
||||||
0,058 |
0,090 |
0,150 |
36,59 |
0,2087 |
|||
42,44 |
0,333 |
||||||
55,43 |
0,435 |
||||||
10,4 |
70,15 |
0,551 |
|||||
10,0 |
11,5 |
86,60 |
0,608 |
||||
11,0 |
0,070 |
0,110 |
0,180 |
12,7 |
104,8 |
0,823 |
|
12,0 |
13,8 |
124,7 |
0,979 |
||||
13,0 |
15,0 |
146,4 |
1,150 |
||||
14,0 |
16,2 |
169,7 |
1,330 |
||||
15,0 |
17,3 |
194,9 |
1,530 |
||||
16,0 |
18,4 |
221,7 |
1,740 |
||||
17,0 |
19,6 |
250,3 |
1,960 |
||||
18,0 |
20,7 |
280,6 |
2,200 |
||||
19,0 |
0,084 |
0,130 |
0,210 |
21,9 |
312,6 |
2,450 |
|
20,0 |
23,0 |
346,4 |
2,720 |
||||
20,8 |
23,9 |
274,7 |
2,940 |
||||
21,0 |
24,2 |
381,9 |
3,000 |
||||
22,0 |
25,4 |
419,2 |
3,290 |
||||
24,0 |
27,7 |
498,8 |
3,920 |
||||
25,0 |
28,8 |
541,3 |
4,250 |
||||
26,0 |
30,0 |
585,4 |
4,600 |
||||
27,0 |
31,2 |
631,3 |
4,960 |
||||
28,0 |
32,3 |
679,0 |
5,330 |
||||
30,0 |
34,6 |
779,4 |
6,120 |
||||
32,0 |
0,100 |
0,160 |
0,250 |
36,9 |
886,8 |
6,96 |
|
34,0 |
39,2 |
1001,0 |
7,86 |
||||
36,0 |
41,6 |
1122,0 |
8,81 |
||||
38,0 |
43,8 |
1251,0 |
9,82 |
||||
40,0 |
46,1 |
1386,0 |
10,88 |
||||
41,0 |
47,3 |
1456,0 |
11,40 |
||||
42,0 |
48,5 |
1527,0 |
11,99 |
||||
45,0 |
51,9 |
1754,0 |
13,77 |
||||
46,0 |
53,1 |
1833,0 |
14,40 |
||||
48,0 |
55,4 |
2000,0 |
15,60 |
||||
50,0 |
57,7 |
2165,0 |
17,00 |
||||
53,0 |
0,120 |
0190 |
0,300 |
61,2 |
2433,0 |
19,1 |
|
55,0 |
63,5 |
2620,0 |
20,6 |
||||
56,0 |
64,6 |
2715,0 |
21,3 |
||||
60,0 |
69,3 |
3118,0 |
24,5 |
||||
63,0 |
72,7 |
3437,0 |
27,0 |
||||
65,0 |
75,0 |
3659,0 |
28,7 |
||||
70,0 |
0,190 |
0,300 |
80,8 |
4244,0 |
33,3 |
||
75,0 |
86,5 |
4871,0 |
38,2 |
||||
80,0 |
92,3 |
5542,0 |
43,5 |
||||
85,0 |
0,220 |
0,350 |
98,0 |
6257,0 |
49,1 |
||
90,0 |
104,0 |
7015,0 |
55,1 |
||||
95,0 |
110,0 |
7816,0 |
61,4 |
||||
100,0 |
115,0 |
8660,0 |
68,0 |
Notes:
1. At the request of the consumer, calibrated hexagonal rolled products are manufactured in other sizes not specified in. The maximum deviations in this case must correspond to the standards established for the nearest larger diameter.
2. The cross-sectional area and linear density of calibrated hexagonal rolled products are calculated based on the nominal size. The rolled product density is assumed to be 7.85 g/cm 3 .
3. For rolled products made from high-alloy steels and alloys subjected to heat treatment and pickling, maximum dimensional deviations are set at 30% more than quality h 12.
(Changed edition, Amendment No. 1, No. 2).
3. Calibrated hexagonal rolled products are produced in rods. At the consumer's request, rolled products are produced in coils.
4. Depending on the purpose, rods are made:
measured length;
multiple measured length;
of unmeasured length with a remainder of up to 10% of the batch mass;
limited length within unmeasured.
The remainder is considered to be rods with a length of at least 1.5 m.
(Changed edition, Amendment No. 1).
5. Rods are manufactured in lengths from 2 to 6.5 m. At the request of the consumer, rods are manufactured in longer lengths.
3-5 (Changed edition, Amendment No. 1).
Points 6, 7 are excluded, Amendment. No. 1).
8. Maximum deviations along the length of bars of measured and multiple measured lengths should not exceed:per 1 m length, mm
full length, %
h10 andh11
h12
h10 andh11
h12
Up to 25
St. 25 to 50
Over 50
The deviation from straightness must be uniform along the entire length. Short longitudinal bends are not allowed at the ends of the rods.
( 10. Twisting of rods per 1 m length () should not exceed 3°.
Crap. 2
(
11. The cut of the rod should be at right angles to its longitudinal axis. The permissible bevel of the cut should not exceed:
0,2 A- for rod sizes up to 15mm;
0,17 A Up to 25
St. 25 to 50
"50"70
2
Up to 25
St. 25
(Introduced additionally, Amendment No. 1).
GOST 8560-78
Group B32
INTERSTATE STANDARD
RENTED CALIBRATED HEXAGON
Assortment
Calibrated hexahedronal rolled-stock. Dimensions
MKS 77.140.50
OKP 11 4000
Date of introduction 1979-07-01
By Decree of the USSR State Committee on Standards dated August 2, 1978 N 2079, the implementation date was set at 07/01/79
The validity period was lifted according to Protocol N 7-95 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-95)
INSTEAD GOST 8560-67
EDITION (October 2012) with Amendments No. 1, 2, approved in April 1983, December 1988 (IUS 7-83, 3-89).
Introduction
1. This standard applies to calibrated hexagonal rolled products ranging in size from 3 to 100 mm.
Dimensions of the rolled section and maximum deviations for them, drawing 1 and table 1
2. The dimensions of the rolled section and the maximum deviations for them must correspond to those indicated in Figure 1 and Table 1.
Table 1
Size | Maximum deviation, mm | Circumcircle diameter, | Maximum deviation, mm | Cross-sectional area, mm | Weight of 1 m length, kg |
||
Notes:
1. At the request of the consumer, calibrated hexagonal rolled products are manufactured in other sizes not listed in Table 1. The maximum deviations in this case must correspond to the standards established for the nearest larger diameter.
2. The cross-sectional area and linear density of calibrated hexagonal rolled products are calculated based on the nominal size. The rolled product density is taken to be 7.85 g/cm.
3. For rolled products made from high-alloy steels and alloys subjected to heat treatment and pickling, maximum dimensional deviations are set at 30% more than h12 quality.
3. Calibrated hexagonal rolled products are produced in rods. At the consumer's request, rolled products are produced in coils.
4. Depending on the purpose, rods are made:
- measured length;
- multiple measured length;
- unmeasured length with a remainder of up to 10% of the batch weight;
- limited length within unmeasured.
The remainder is considered to be rods with a length of at least 1.5 m.
5. Rods are manufactured in lengths from 2 to 6.5 m. At the request of the consumer, rods are manufactured in longer lengths.
3-5. (Changed edition, Amendment No. 1).
6, 7. (Excluded, Amendment No. 1).
8. Maximum deviations along the length of bars of measured and multiple measured lengths should not exceed:
+30 mm - for rod lengths up to 4 m;
+50 mm - for rod lengths over 4 m.
Curvature of rods, table 2, drawing 2
9. The curvature of the rods should not exceed the values indicated in Table 2.
Table 2
Rod size, mm | Limit curvature depending on the tolerance range |
|||
per 1 m length, mm | full length, % |
|||
St. 25 "50 | ||||
The deviation from straightness must be uniform along the entire length. Short longitudinal bends are not allowed at the ends of the rods.
10. Twisting of rods per 1 m length (Fig. 2) should not exceed 3°.
11. The cut of the rod should be at right angles to its longitudinal axis. The permissible bevel of the cut should not exceed:
0.17 - for rod sizes up to 16 mm;
3 mm - for rod sizes over 16 to 30 mm;
5 mm - for rod sizes over 30 mm.
9-11. (Changed edition, Amendment No. 1).
Length of crumpled ends of rods, table 3
12. The length of the crumpled ends of the rods should not exceed the standards specified in Table 3.
Table 3
Bar size | Length of crumpled ends, no more |
St. 25 "50 | |
(Introduced additionally, Amendment No. 1).
Radius of edges, table 4
13. The radius of the edges is determined at the request of the consumer and should not exceed the values specified in Table 4.
Table 4
Bar size | Radius of rounding of edges for a group, no more |
|
(Changed edition, Amendment No. 1, 2).
Electronic document text
prepared by Kodeks JSC and verified against:
official publication
Rolled steel sheets.
Assortment: Sat. GOST. -
M.: Standartinform, 2012
INTERSTATE STANDARD
01.07.79
The validity period was lifted according to Protocol No. 7-95 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-95)
1. This standard applies to calibrated hexagonal rolled products ranging in size from 3 to 100 mm.
2. The dimensions of the rolled section and the maximum deviations for them must correspond to those indicated in the drawing. 1 and in table. 1.
Table 1
Rolled size (diameter of inscribed circle A or turnkey size), mm |
Maximum deviation, mm |
Diameter of circumscribed circle, A, mm |
Maximum deviation, mm |
Cross-sectional area, mm 2 |
Weight of 1 m length, kg |
||
Notes:
1. At the request of the consumer, calibrated hexagonal rolled products are manufactured in other sizes not listed in the table. 1. Limit deviations in this case must correspond to the standards established for the nearest larger diameter.
Measured length;
Multiple measured length;
Unmeasured length with a remainder of up to 10% of the batch weight;
Limited length within unmeasured.
The remainder is considered to be rods with a length of at least 1.5 m.
50 mm - for rod lengths over 4 m.
9. The curvature of the rods should not exceed the values indicated in the table. 2.
Table 2
The deviation from straightness must be uniform along the entire length. Short longitudinal bends are not allowed at the ends of the rods.
10. Twisting of rods per 1 m length a (Fig. 2) should not exceed 3°.
11. The cut of the rod should be at right angles to its longitudinal axis. The permissible bevel of the cut should not exceed:
0,17A- for rod sizes up to 16 mm;
3 mm - for rod sizes over 16 to 30 mm.
5 mm - for rod sizes over 30 mm.
9 - 11. (Changed edition, Amendment No. 1).
GOST 8560-78
INTERSTATE STANDARD
RENTED CALIBRATED HEXAGON
ASSORTMENT
Official publication
Standardinform
INTERSTATE STANDARD
ROLLED CALIBRATED HEXAGONAL Assortment
Calibrated hexahedronal rolled-stock. Dimensions Instead
GOST 8560-67
MKS 77.140.50 OKP I 4000
By Decree of the USSR State Committee on Standards dated August 2, 1978 No. 2079, the introduction date was set
The validity period was lifted according to Protocol No. 7-95 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-95)
1. This standard applies to calibrated hexagonal rolled products ranging in size from 3 to 100 mm.
2. The dimensions of the rolled section and the maximum deviations for them must correspond to those indicated in the drawing. 1 and in table. 1.
Rolled size (diameter of inscribed circle a or turnkey size), mm |
Maximum deviation, mm |
Diameter of circumscribed circle, A, mm |
Limit deviation, |
Cross-sectional area, mm * 1 2 |
Weight of 1 m length, kg |
||
Official publication Reproduction prohibited
(IUS 7-83, 3-89).
© Standards Publishing House, 1978 © Standartinform, 2008
Continuation of the table. 1
Rental size |
Maximum deviation, mm | ||||||
(diameter in- |
Limit | ||||||
described |
|||||||
luge circle a |
circles, |
deviation, |
transverse |
LENGTHS, kg |
|||
or size |
section, mm z |
||||||
"turnkey"), mm | |||||||
Notes:
1. At the request of the consumer, calibrated hexagonal rolled products are manufactured in other sizes not listed in the table. 1. Limit deviations in this case must correspond to the standards established for the nearest larger diameter.
2. The cross-sectional area and linear density of calibrated hexagonal rolled products are calculated based on the nominal size. The rolled product density is taken to be 7.85 g/cm 3 .
3. For rolled products made from high-alloy steels and alloys subjected to heat treatment and pickling, maximum dimensional deviations are set at 30% more than hl2 quality.
3. Calibrated hexagonal rolled products are produced in rods. At the consumer's request, rolled products are produced in coils.
4. Depending on the purpose, rods are made:
Measured length;
Multiple measured length;
Unmeasured length with a remainder of up to 10% of the batch weight;
Limited length within unmeasured.
The remainder is considered to be rods with a length of at least 1.5 m.
5. Rods are manufactured in lengths from 2 to 6.5 m. At the request of the consumer, rods are manufactured in longer lengths.
3-5. (Changed edition, Amendment No. 1).
6. 7. (Excluded, Amendment No. 1).
8. Maximum deviations along the length of bars of measured and multiple measured lengths should not exceed:
30 mm - for rod lengths up to 4 m;
50 mm - for rod lengths over 4 m.
9. The curvature of the rods should not exceed the values indicated in the table. 2.
Table 2
The deviation from straightness must be uniform along the entire length. Short longitudinal bends are not allowed at the ends of the rods.
10. Twisting of rods per 1 m length a (Fig. 2) should not exceed 3°.
11. The cut of the rod should be at right angles to its longitudinal axis. The permissible bevel of the cut should not exceed:
0.17 a - for rod sizes up to 16 mm;
3 mm - for rod sizes over 16 to 30 mm.
5 mm - for rod sizes over 30 mm.
9-11. (Changed edition, Amendment No. 1).
12. The length of the crumpled ends of the rods should not exceed the standards specified in the table. 3.
Table 3
(Introduced additionally, Amendment No. 1).
13. The radius of curvature of the edges is determined at the request of the consumer and should not exceed the values specified in the table. 4.
Table 4
Radius of rounding of edges for a group, no more
Bar size
Up to 25 Up to 25
(Changed edition, Amendment No. 1, 2).
Editor V.N. Kopysov Technical editor YES. Guseva Corrector E.D. Dulneva Computer layout A.N. Zolotareva
Signed for publication on 02/08/2008. Format 60X84 1/". Offset paper. Times typeface. Offset printing. Uel.bake.l. 0.93.
Academician-ed.l. 0.40. Circulation 63 copies. Zach. 97.
FSUE "STANDARTINFORM", 123995 Moscow, Granatny lane, 4.
Typed into FSUE "STANDARTINFORM" on a PC.
Printed in the branch of FSUE "STANDARTINFORM" - type. "Moscow Printer", 105062 Moscow, Lyalin lane, 6.
INTERSTATE STANDARD
RENTED CALIBRATED HEXAGON |
GOST 8560—78 |
Assortment Calibrated hexahedronal rolled-stock. Dimensions MKS 77.140.50 |
In return GOST 8560—67 |
By Decree of the USSR State Committee on Standards dated August 2, 1978 No. 2079, the introduction date was set
01.07.79
The validity period was lifted according to Protocol No. 7-95 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-95)
- This standard applies to calibrated hexagonal rolled products ranging in size from 3 to 100 mm.
- The dimensions of the rolled section and the maximum deviations for them must correspond to those indicated in the drawing. 1 and in table. 1.
A or turnkey size), mm |
Maximum deviation, mm |
Circumcircle diameter, |
Limit deviation, |
Weight l m length, kg |
|||
Official publication
Reproduction is prohibited
Edition (September 2005) with Amendments No. 1, 2, approved in April 1983, December 1988 (IUS 7-83, 3-89).
Standards Publishing House, 1978
Standardinform, 2005
Continuation of the table. 1
Rolled size (diameter of inscribed circle A or turnkey size), mm |
Maximum deviation, mm |
Circumcircle diameter, |
Limit deviation, |
Cross-sectional area, mm 2 |
Weight l m length, kg |
||
Notes:
- At the request of the consumer, calibrated hexagonal rolled products are manufactured in other sizes not listed in the table. 1. Limit deviations in this case must correspond to the standards established for the nearest larger diameter.
- The cross-sectional area and linear density of calibrated hexagonal rolled products are calculated based on the nominal size. The rolled product density is taken to be 7.85 g/cm 3 .
- For rolled products made from high-alloy steels and alloys subjected to heat treatment and pickling, maximum dimensional deviations are set at 30% more than quality h
- Calibrated hexagonal rolled products are produced in rods. At the consumer's request, rolled products are produced in coils.
- Depending on the purpose, rods are manufactured:
Measured length;
Multiple measured length;
Unmeasured length with a remainder of up to 10% of the batch weight;
Limited length within unmeasured.
The remainder is considered to be rods with a length of at least 1.5 m.
- Rods are manufactured in lengths from 2 to 6.5 m. At the request of the consumer, rods are manufactured in longer lengths.
3—5.
6, 7. (Excluded, Amendment No. 1).
- Maximum deviations along the length of rods of measured and multiple measured lengths should not exceed:
30 mm - for rod lengths up to 4 m;
50 mm - for rod lengths over 4 m.
- The curvature of the rods should not exceed the values indicated in the table. 2.
Table 2
The deviation from straightness must be uniform along the entire length. Short longitudinal bends are not allowed at the ends of the rods.
- Twisting of rods per 1 m length α (Fig. 2) should not exceed 3°.
- The cut of the rod should be at right angles to its longitudinal axis. The permissible bevel of the cut should not exceed:
0.17 α - for rod sizes up to 16 mm;
3 mm - for rod sizes over 16 to 30 mm.
5 mm - for rod sizes over 30 mm.
9—11. (Changed edition, Amendment No. 1).
- The length of the crumpled ends of the rods should not exceed the standards indicated in the table. 3.
Table 3
(Introduced additionally, Amendment No. 1).
- The radius of curvature of the edges is determined at the request of the consumer and should not exceed the values specified in the table. 4.
Table 4
(Changed edition, Amendment No. 1, 2).
Editor V.N. Kopysov
Technical editor L.A. Gusev
Proofreader E.D. Dulneva
Computer layout A.N. Zolotareva
Signed for publication on September 22, 2005. Format 60x841/8. Offset paper. Times typeface. Offset printing. Cond.bake.l. 0.93.
Academician-ed.l. 0.40. Circulation 176 copies. Zach. 760. Since 1987.
FSUE "Standartinform", 123995 Moscow, Granatny per., 4.
Typed in IPK Publishing House of Standards for PC.
Printed in the branch of FSUE "Standardinform" - type. "Moscow Printer", 105062 Moscow, Lyalin lane, 6.